An important aspect of scouting is the accurate identification of pests. Lumping insects into the general category of worms or identifying weeds only as grasses is a mistake. Knowing precisely which insect, weed, or disease is in a field is important. When control decisions are made, this information allows the grower to design a specific treatment plan instead of wasting money on a "shotgun" approach. Identifying diseases and weeds will also help when planning rotations and selecting varieties.

Avoid the temptation to make pest control decisions for several fields based only on information from one or two fields. Pest levels can vary greatly from one field to another, even though the fields appear similar.

Each field should be checked closely, or scouted, once a week. On each of these scouting trips, the grower should take samples, or stop at predetermined locations in the field and examine plants. The chart tells how many stops should be made, or samples taken, per field and how many plants should be examined per sample.

When stopping to take a sample, look first for any pests that might jump or fly off the plant (for example, flea beetles). Look for pests on both sides of the leaves of the five plants to be examined at each stop. Most pests will be found in the top half of the plant, but don't ignore the lower half. Do not look for a particular pest; take note of all pests found on a plant. Once you have finished checking the fiveplant sample, look around the area and make note of any problems.

Occasionally a field should be checked again in less than a week. For example, if a high number of small hornworms (less than 1 inch long) are found, but the field does not contain enough large hornworms to be at threshold, then it should be scouted again in two or three days. Similarly, a second scouting trip within a week is called for if aphids are found on a large number of plants, but the aphid colonies are just below the size at which the plants could be counted as infested.

There are several points to remember when scouting tobacco:

1. Before entering a field, look at its shape and determine an overall sampling pattern to cover the whole field. Once in a field, the spots where samples are taken must be selected randomly. Devise a routine to identify the exact spot at which the next stop will be made. Decide, for example, that once you get to the general area of the next sample you will take the sample two rows over from your present position and 10 plants down. Take a sample in that spot unless there is a skip in the row. In that case, take a sample at least two rows over from where you would have stopped had there not been a skip in the row.
   
2. Do not use the same pattern or enter the field at the same location each week. It is very easy to fall into the habit of entering the field in the same place each week, perhaps because there is a convenient place to park nearby. Develop three or four patterns and rotate their use.
   
   
   
   Figure 1. Field scouting pattern.
   
3. Do not sample within four rows or 20 feet of the field edge. Do, however, make general observations along field edges as some problems can begin in this area.
   
4. Do not wait for a spot with obvious damage to begin sampling or skip a spot because it has obvious damage. Decide where to stop beforehand and take a sample of whatever is found at that location.
   
5. When walking a field, watch for dying or stunted plants. If any are observed, try to identify the reason. If the cause is not readily apparent, dig up a plant (including roots) and take it to the county Extension agent for diagnosis.
   
6. On each field visit, it is always useful to record some general comments on field conditions, pest levels, agronomic problems, etc. Note localized problems that may not have shown up in any of the samples. Always be alert for agronomic or unexplained problems. Contact the county Extension agent for help with problems that are difficult to diagnose.
   
   

The number of pests or level of crop damage at which it pays to spend money on a pesticide treatment is the economic threshold for a pest. Most tobacco growers already do a good job of watching their crop and monitoring the activities of pests. When pests are found, however, some growers have trouble deciding whether a pesticide treatment is justified. This is where thresholds can help. Some growers do not realize that the first sign of pests in tobacco is not necessarily the proper time to consider control.

One might think that if pests are present they must be damaging the crop or interfering with its growth, thus causing a loss. Actually, pests can sometimes build to relatively large numbers before it pays to control them. For example, undamaged leaves of a tobacco plant may grow larger or the plant may add weight to compensate for some insect damage. Also, the crop may simply out compete a low level of weeds. Treating for a pest that will not reduce the quality or yield of the crop is a waste of money.

Another point to consider is that natural control agents are almost always working against an increase in pest levels. In other words, the existence of a pest does not guarantee the pest will ever reach damaging levels. There is no point in spending money to control a pest that may never build to damaging levels. Waiting to see if there will be enough pests to warrant treating is one of the ways Integrated Pest Management works to save growers money.

Keep in mind that although the thresholds given in this manual have worked very well, they were developed as guidelines for average conditions. In unusual situations, such as during periods of drought stress or when multiple pests are present, lower thresholds should be used.

Pesticide Selection and Application
Once a pest exceeds the economic threshold, the grower must determine the best and least expensive way to prevent unacceptable losses. If a pesticide treatment is needed, the pesticide and its rate and method of application must be customized to the pest. This is probably the surest way to save money. High pesticide rates are not needed if the correct pesticide is chosen and the method of application delivers the needed amount of chemical to the pest. To apply pesticides properly, sprayer pressure and volume must be correct; the right nozzle type, arrangement, and number must be used; and the sprayer must be accurately calibrated.

Specific pesticide recommendations are not included in this guide. When deciding on a pesticide, talk to your local Extension agent and consult the North Carolina Agricultural Chemicals Manual or Tobacco Information before talking to your chemical supplier.

Tobacco Scouting Calendar
Certain pests pose greater threats to tobacco than others during different times of the growing season. The scout should be particularly diligent in looking for the pests that are likely to do the most damage. The pest calendar (below) lists the scouting activities or pests to which special attention should be paid at various times after transplanting. The calendar is intended as a general guide. Pest problems may sometimes occur at unusual times. Pests occurring at unexpected times cause the greatest problems. Fields should be scouted regularly and systematically in order to prevent unnecessary losses.

Weeks After Transplanting	Pests or Scouting Activity
1 and 2	flea beetles, cutworms; check stand
3	flea beetles, cutworms, wireworm injury, weeds
4	flea beetles, cutworms, budworms, wireworm injury
5 and 6	budworms, aphids
7 and 8	budworms, aphids; buttoning
9	aphids, flea beetles, hornworms
10, 11, and 12	aphids, flea beetles, hornworms; sucker control, disease survey
13	flea beetles, hornworms; sucker control
14	flea beetles, hornworms; weed survey
15--until harvest is complete	flea beetles, hornworms

---

Scouting Tobacco in North Carolina

Troubleshooting Tobacco